Asus E500-PIB Podręcznik Użytkownika Pobierz pdf (Strona 34)

30 • Schlage • Schlage Utility Soware User's Guide

Lock PropertiesAD-Series Locks and Controllers

AD-400 (Networked Locks)

EDIT Tab

Property Description Default

Heartbeat The heartbeat is a brief communication from the lock to the PIM400. It allows an

idle lock to check for messages. Range: 15 seconds - many hours.

The value indicates the time between the heartbeats. Set to a shorter time (lower

number) for more frequent communication. Set to a longer time (higher number)

for less frequent communication. A smaller value will decrease battery life. A larger

value will increase battery life.

10 minutes

Comm Loss Fail Mode Lock state set when RF communication with the linked PIM400 fails.

States: As-Is, Secure/Lock, Unsecure/Unlock

As-Is

Allow Extended Unlocks

(Locks linked to

PIM400-TD2 only)

Extended unlock permits the lock to stay in an indeﬁnite unlock state.

Enabling the Extended Unlock feature is required to implement a scheduled unlock

period from an ACP.

Enabled

Report RTX for Host to

unlock

Determines how an AD-400 will handle a request to exit.

If disabled, the AD-400 will only report that a request to exit has occurred. Disable

if the access point does not need to be electronically unlocked to provide egress

(if equipped with a crash bar) but the access control panel needs to be notiﬁed so

that a forced door does not occur.

If enabled, the AD-400 will report that a request to exit has occurred, and also will

query the PIM400 to determine if the AD-400 should be electronically unlocked.

Use this mode if the AD-400 needs to be electronically unlocked in order to provide

egress.

Disabled

Relatch Aer:

Timer/Door Status

Re-latch on:

• Timer Only (Lock when Timer expires (default 3 seconds) regardless of Door

status or Position)

• On Door Open or Timer (Lock when the Door opens or Timer expires)

• On Door Close or Timer (Lock when the Door closes or Timer expires)

Timer only

High Low Output

(Locks linked to

PIM400-TD2 only)

Polarity of the Request-to-Exit (RTX) signal. Low: RTX

Polarity of the Request-to-Enter (RTE) signal. Low: RTE

Polarity of the On Door Open, (Door Position Switch (DPS)) signal. High: open

Polarity of Trouble signal. Low: trouble

First, Delay, Retry First: First query a Lock makes to a PIM400 occurs immediately following

presentation of a credential. First is the amount of time, in milliseconds, an AD-

400 should wait before making its second query to a PIM400. This setting should

be slightly greater than the fastest response time from the access control panel or

host. This optimizes battery life and system performance.

Delay: The idle time between subsequent queries. Shorter delays may reduce

latency. Longer delays may enhance battery life.

Retry: The maximum number of times an access point queries a PIM400 before

the Lock goes back to sleep. The number of retries should be slightly greater than

the longest response time from the access control panel or host. Retrys = [{Max

Response Time of Panel- First}/Delay] +1

First: 300

msec.

Delay: 200

msec.

Retry: 5

Degraded (Cache)

Mode: Card Bit Format

Enter the number of bits in the credential card number.

0 = Degraded (Cache) mode disabled

1. These properties are view-only when the HHD is connected to the lock. Connect the HHD to the PIM400 to make changes.

1 2 ... 29 30 31 32 33 34 35 36 37 38 39 ... 86 87

Komentarze do niniejszej Instrukcji

Brak uwag

Asus E500-PIB Podręcznik Użytkownika Strona 34

Komentarze do niniejszej Instrukcji